0

DCS Training Course

4.5
(6)
189 Enrolled

About Course

A PRACTICAL TRAINING COURSE ON DCS

What do you get with this?

Lifetime access +Training certificate+ Member of the biggest community (+10k member)of control &instrumentation + regular job updates & Interview Guidance( members got job and many pramoted in their job)+ Abroad job guidance

What Will You Learn?

  • Training session-1
  • 1.1 Project creation
  • 1.2 ASSIGINING OF FCS
  • 1.3 Node creation
  •  1.4 Input & output module creation
  •  1.5Labelling of IOM
  • Training session -02
  • 2.1 Function block introduction
  • 2.2 Drawing page nomination
  • 2.3 Programming for Open loop creation
  • 2.4 Programming for Close loop creation
  • Training session-03
  • 3.1 Programming for Cascade loop creation
  • Training session -04
  • 4.1Programming for creation of new close loop
  • 4.2 Operation of new close loop on HMI
  • Training session -05
  • 5.1 Learning operation of cascade loop HMI
  • Training session -06
  • 6.1 Concept of FOUT loop
  • 6.2 Difference between FOUT loop & Cascade loop
  • 6.3Programming with FOUT loop
  • 6.4Grouping of FACEPLATE
  • 6.5Operation of FOUT on HMI
  • Training session -07
  • 7.1Control signal splitter (SPLIT)
  • 7.2Operation of SPLIT
  • 7.3Switch setting in SPLIT
  • Training session -08
  • 8.1 Logic creation with auto selector
  • 8.2 Operation of auto selector on HMI
  • Training session-09
  • 9.1Logic creation with signal selector
  • 9.2 Operation of logic created by signal selector
  • Training session -10
  • 10.1 Concept of arithmetic block
  • In that we will do programming for
  • Addition
  • Divide
  • Subtract
  • 10.2 Average
  • Training session-11
  • 11.1 Velocity limiter block (VELLM)
  • Training session-12
  • 12.1 Concept of Calcu (Calculation) block
  • 12.2 Programming with Calcu block (AND, OR logic creation)
  • Training session-13
  • 13.1 Concept of ST16
  • 13.2 Programming for AND logic by ST16
  • 13.3 Programming for two valve operation on Alarm status
  • 13.4 Programming for Auto-Manual changeover over of PID based on condition change
  • Training session-14
  • 14.1Programming for Motor control block
  • 14.2 Operation of motor control block on HMI
  • Training session -15
  • 15.1 Logic creation by LC64
  • 15.2 Operation of LC-64 Block on HMI
  • Training session-16
  • 16.1Concept of trend
  • 16.2 Trend setting
Show More

Course Content

lesson 1

  • 1
    14:24

lesson 2

lesson 3

lesson 4

lesson 5

lesson 6

lesson 7

lesson 8

lesson 9

lesson 10

Lesson 11

Lesson 12

Lesson 13

Lesson 14

Lesson 15

Lesson 16

Instructors

A

Ankur

4.4
402 Students
3 Courses

Feedback

4.5
Total 5 Ratings
66.666666666667%
16.666666666667%
16.666666666667%
0%
0%

Reviews (5)

  1. D

    dayama81

    1 month ago
    Good explanation of all concept of DCS
  2. S

    sahadsulaimanvk

    2 months ago
    Good
  3. M

    Mouli

    5 months ago
    ok
  4. KK

    Keerthi Kumar

    5 months ago
    very useful
  5. DN

    Debarghya Nanda

    7 months ago
    overall good
Open chat
1
Scan the code
Hello 👋
Can we help you?